20' Center Console Inshore
  • LOA                      20'
  • Beam                    8'
  • LBS                 3600
  • HP               90-200
  • Deadrise   26, 14.5
  • Draft               14.75''
  • Air draft             90''
  • Fuel              50gall
  • WOT 150h   43mph
  • Plane           24mph
  • Cruise       4.2 MPG
  • Chine          3.5deg
  • Transom            25''
  • Set Back              4''
  • HULL
  • Modified V
  • 5086 Marine grade alloy
  • 1/4'' bottom plate
  • 3/16'' Hull side
  • keel 3/8 plate one piece
  • 5 frames, water tight bulkhead (NO FOAM)
  • Full height stringers
  • Seamless, radius gunwale
  • Hull turning skeg
  • self bailing
  • Leaning post integrated tackle center
  • Options
  • Tempered glass windshield
  • PlasDeck synthetic decking
  • Power roll out cooler Engel cooler
  • Rod holders- ttop x 5 rail X 7
  • Ski pole-nylon swivel
  • Swim ladder- flush mount
  • USB charge port
  • Lumitec LED dual color flood x3
  • Chart light dual red/white dimmable
  • Courtesy lighting/all compartments 
  • additional seating
  • Rigging
  • Freeman deck hatch
  • SeaStar recessed helm
  • All Tinned wire/heat shrink connections
  • Optima battery
  • Low voltage disconnect switch
  • Factory fuel filter 90 gph
  • BlueSea electrical panel
  • Accon Marine pop up cleats/nav
  • EPA sealed fuel system
  • RULE auto/man bilge 
  • front console entry

This is the FIRST cad welded aluminum boat to ever be built with a seamless radius gunwale edge.  This eliminated the need for a rub rail, makes cleaning a breeze, prevents unwanted line chafing, is stronger and also looks sexy!  She is powered with a Yamaha 150hp pushing her 2700lb hull to 43MPH.   Turns on a rail due to a keel skeg that is located directly under our leaning post.  Large reverse chines give a dry ride and keeps her on plane @ 24mph.  The modified V hull has 26 degrees of dead rise mid ship transitioning to 14.5 at the transom.  This makes better than 4.0 MPG achievable, up at the bow entry 45 degrees easily cuts up anything. 

 

Her deck is finished with glow in the dark holly lines separated by a natural teak colored synthetic decking from Plasdec USA.  There azure product can hold the suns charge for up to 11hrs!  On the rail are 7 flush rod holders angled to not only drift a spread of 3 rods but can also troll 3 at a time.  Up top has an additional 5 rod rocket launcher.  We partnered with Engel coolers and built our leaning post around there 65-gall roto molded cooler.  We then designed a custom roll out cooler hinge powered by Lenco marine to provide stable seating, and fully retracted makes for a spacious aft deck.  A built in Plano tackle center was integrated into the leaning post and is accessible by 2 stainless gas lifts that open the gasketed top.  Hands free latches secure the access hatch also providing a spacious rigging table after picking your weapon of choice. 

 

The T-top is finished off with a composite hard top, dual color dimmable Lumitec lighting, chart light, electronics box.  All of our stowage compartments are led lite along with courtesy lighting.  The console is wide open with front access leaving room for ventilated dry gear.  All of your maintenance items are easy access through two transom hatch doors and also providing additional stowage compartment.  For decades the military and first responders have relied on Plate Welded Aluminum boats.  This is the start of our pleasure boat line the will top out at 40’.   Call anytime 401-864-7267 to find out what I can do for you.

“Thanks for the demo! Insanely well built and dry aluminum center console, solid as a tank but with a luxury feel, well finished. Handles like a sport boat but steady as a dock when idle. Nice work! @one3 is definitely the future of aluminum boats on the Atlantic!”       Josh Comerford  Point Judith RI
Inboard
Hull
One3 Powerboats